MB102 Breadboard
£2.80
In stock
A breadboard (a.k.a ‘Plugboard/Terminal Array Board’) is a way of constructing electronics without having to use a soldering iron. Components are pushed into the sockets on the breadboard and then extra ‘jumper’ wires are used to make connections, this easily allows components to be removed and used again on other projects.
Features:
- 830 Points
- Silver plated contacts
- Features numbered markings to identify each contact point
- Detachable bus strips
Specifications:
- Suitable for 0.4-0.7mm wire diameter
- Dimensions: 16.5cm x 5.5cm x 1cm
| Weight | 45 g |
|---|---|
| Dimensions | 16.5 × 5.5 × 1 cm |
| Soldered | Header pins soldered on |
| Not Soldered | Header pins not soldered onto board |
You may also like…
-
ESP-12F WIFI Development Board
£5.50Add to basketThe core processor of the ESP-F module uses the cost-effective chip ESP8266EX. The chip integrates the industry-leading Tensilica’s L106 ultra-low-power 32-bit micro-MCU in a smaller package with 16-bit Lite mode, supporting 80 MHz and 160 MHz at the main frequency and supporting RTOS. The ESP8266EX has a full Wi-Fi network function that can be used …
-
Double Side Universal PCB Prototype Board
£2.17 – £2.97Select optionsDouble Side Universal PCB Prototype Board Prototyping PCB Board which is widely used for electronic experiments and point-to-point DIY soldering projects. With pre-tinned holes on the board you can easily install any sensors and components you need. Features: Pre-tinned plated holes on the board make it very handy to solder components and sensors for your …
-
Proto Shield for D1 MINI
£2.00Add to basketProto Shield for D1 MINI Solder your own components onto this protoshield and connect it to your D1 MINI. The module also includes 2 x 8 pin male-male headers (require soldering) that allow the module to be easily inserted into the D1 mini headers. Features: Double Sided PCB Dimensions: 28mm x 25mm Hole pitch: 0.1″ …
-
Dupont Connector 2.54mm Kit
£7.99Add to basketDupont Connector 2.54mm Kit – 310PCS Allows you to make cable connectors for Arduino or Raspberry Pi projects. Features: 100PCS Female Crimp Pins 100PCS Male Crimp Pins 30PCS 1X1P 20PCS 1X2P 20PCS 1X3P 10PCS 1X4P 10PCS 1X5P 10PCS 1X6P 10PCS 1X8P Wire Gauge: 22-28AWG Pin Spacing: 2.54mm (0.1″)
Related products
-
Maplin SIM900 GPRS/GSM Shield for Arduino
£6.50Read moreMaplin SIM900 GPRS/GSM for Arduino The SIM900 GSM/GPRS Shield provides you a way to use the GSM cell phone network to receive data from a remote location. The shield allows you to achieve this via any of the three methods: Short Message Service Audio GPRS Service The GPRS Shield is compatible with all …
-
18650 Battery Holder
£2.00 – £2.75Select optionsBattery holder for 18650 3.7V Batteries in multiple configurations all including 10cm connection wires. Commonly used in conjunction with a charging circuit/solar source to power off grid Arduino/Raspberry Pi projects, such as a 5V Solar Panel – 1.25W 250mA coupled with a Li-ion 18650 Step Up Battery Charger Board Features: Fits standard 1860 Battery with …
-
18650 Battery Holder – Single
£2.00Add to basket18650 Battery Holder – Single Single holder for 18650 3.7V Battery in Single configuration inc. Wires. Commonly used in conjunction with a charging circuit/solar source to power off grid Arduino/Raspberry Pi projects. Features: Fits standard 1860 Battery with button top 10cm wires Specifications: Material: PBT RoHS Compliant Flammability: UL 94V-0
-
WIFI 2.4G 3dbi PCB Antenna IPX IPEX
£1.50Add to basketWIFI 2.4G 3dbi PCB Antenna IPX IPEX Suitable for IEEE 802.11 b/g/n WLAN Systems, Wireless Communication Systems, WiMAX / MIMO Systems and Laptop/Bluetooth/Zigbee antennas. Versatile and small with a standard IPEX Connector Specifications: Frequency 2400 ~ 2500 MHz S.W.R. <= 2.0 Antenna Gain 3.0 ± 0.7dBi Polarization Linear Impedance 50 Ohm Material of …